TNC F 4 HOLE SOLDER
- Prepare the Cable:
– Strip the Outer Jacket: Use a cable stripping tool to remove approximately 1/4 to 1/2 inch (or as specified by the connector manufacturer) of the outer jacket from the coaxial cable. Be careful not to damage the underlying braided shield.
– Expose the Shielding: Pull back the braided shield to reveal the dielectric insulation. Trim any excess shielding so that it fits neatly inside the connector.
– Strip the Dielectric: Strip the dielectric insulation to expose the center conductor. The length of the exposed center conductor should be about 1/4 inch, but refer to the connector’s specifications for exact requirements. - Prepare the Connector:
– Insert the Cable: Insert the prepared end of the coaxial cable through the connector. Align the center conductor with the center pin of the connector, and ensure that the shield makes good contact with the connector body. - Solder the Connector:
– Heat the Soldering Iron: Preheat your soldering iron to around 350°C (662°F). Clean the tip of the soldering iron to ensure good thermal conductivity.
– Apply Soldering Flux: Apply a small amount of soldering flux to the PCB pads and connector pins. This helps the solder flow more smoothly and ensures a good bond.
– Solder the Center Pin: Heat the center pin with the soldering iron tip. Feed solder into the joint while keeping the iron in contact with the pin and pad. Remove the soldering iron once the solder has flowed evenly around the joint.
– Solder the Shield: If the connector has solder pads for the shield, apply solder to secure the braided shield to the connector’s body. Make sure the shield is well-soldered to provide a good grounding connection. - Mount and Secure:
– Mount the Connector: If the TNC female connector is intended for panel mounting, secure it using the provided mounting hardware. Ensure it is tightened properly to avoid movement or strain on the soldered connections. - Inspect and Clean:
– Check Solder Joints: Inspect each solder joint to ensure there are no cold or weak joints. A good solder joint should be smooth and shiny.
– Look for Solder Bridges: Ensure there are no solder bridges between adjacent pins or pads. Use a solder wick or desoldering pump to remove any excess solder if needed.
– Clean the PCB: Use a PCB cleaning solution or isopropyl alcohol to clean off any residual soldering flux from the PCB. - Test the Connection:
– Verify Connections: Ensure the connector is securely attached and that there are no loose parts.
– Test Signal: Use appropriate testing equipment to confirm that the connection is functioning correctly and that there are no signal issues.
₹99
⚡ 🚚 Lightning Fast Delivery in 4-7 Business Days – Pan India
💸 Cash On Delivery Available
💰 Lowest Prices
The prices on our website are the lowest. Don’t trust us, compare it with Amazon or Flipkart immediately. If you ever find our prices higher than any website, let us match it for you.
The TNC Female 4-Hole Solder connector is designed for mounting on panels, featuring a 4-hole flange for secure attachment. This connector requires soldering, offering a strong, stable connection with excellent electrical performance. It is suitable for a wide range of RF applications, handling frequencies up to 11 GHz. The TNC Female 4-Hole Solder connector is ideal for environments where vibration or movement may be a concern, ensuring long-term reliability.
Tools and Materials Needed:
1. TNC Female 4-Hole Solder Connector
2. Coaxial Cable (e.g., RG-58, RG-59, RG-6, or similar)
3. Cable Stripping Tool (suitable for your cable type)
4. Soldering Iron (with a fine tip)
5. Solder (preferably lead-free solder or as specified)
6. Soldering Flux (optional but recommended for better solder flow)
7. PCB Cleaning Solution (for cleaning after soldering, if needed)
8. Tweezers (for positioning the connector)
9. Small Wire Cutters (for trimming excess leads)
| Weight | 0.1 kg |
|---|
Free Shipping
On orders above 999/-
14 Days Return
No Questions Asked
Secure Payment
Secure Server
100% GST Bill
All Original Products
Proudly Made in India
Teleten has always been a staunch supporter and advocator of Make In India. We live in the most diversified country with unmatched talent and creativity. We are the biggest democracy in the world with second largest population. As an organization, we firmly believe that the whole society needs to grow to facilitate a holistic development of any company/organisation.
Considering the ongoing pandemic, we realise that the need of the hour is to boost our organization in our own backyard. We aim to raise employment opportunities from an already existent Indian talent base, towards a better and a sustainable future. In order to achieve this we must:
Buy Any Indian Product.
But Buy Only Indian Products.
Be Vocal for Local.
We are proud to be the part of this great initiative by Indian Government. We hope more people understand the importance of this initiative and more consumers become rational to buy only Indian products.
We Understand You Can Still Have Questions
Do you have a doubt or a concern? Not sure what to get yet? Dont know what will work best for you? No problem. Our technical team can answer all your questions.
Related products
-
Sale!
-
Sale!
-
Sale!
-
Sale!
